Simple Wire-Wrapped Ring Tutorial

觉得这个好酷哦!很想自己试试的说!Open-mouthed smile

There are a lot of complex wire-wrapped ring tutorials out there, and I’ll be honest – this isn’t one of them. This is about as “intro” as they come – a basic, simple wire wrapped ring with a single 8mm bead focal. For those of you just getting started with wire jewelry making, this is a terrific way to get your feet wet. With this design, you can create a colorful bit of bling in just a few minutes with a bit of inexpensive 20 or 22 gauge Artistic wire, an 8mm bead, and the necessary tools. I won’t admit to how many of these rings are in my jewelry box – but a girl just has to have a ring to match, well, anything!

Parts Suggested

    Step 1

    Cut a length of wire about 12″ long. Put the 8mm bead in the middle of the wire, and lay it flat on the mandrel at the line indicating your chosen ring size. Wrap either end of wire around the mandrel and bring it back ot the front so the wire ends lie to either side of the 8mm focal bead.

    Step 2

    Firmly gripping the wire so it stays taunt, cross the wires around the bead.

    Step 3

    Again, keeping the wires taught, cross the wires again. As you cross the wires, you want the newly wrapped wire to lay underneath the previous crossed wire.

    Step 4

    Keeping wrapping the wires around the circle of the bead, keeping pressure on the wire for, and making each new layer wrapped underneath the previous layer.

    Step 5

    When you have either four or five wraps (my preference), then you’re finished wrapping around the bead, and it is time to finish the sides.

    Step 6

    Before wrapping the sides, clip the excess wire – give yourself about 1.5″ of wire on both sides to finish the ring with.

    Step 6

    Wrap the tail of the wire around one side of the ring. Keep firm pressure on the wire to make nice, neat loops.

    Step 8

    When you have three or four loops, snip off the excess wire with your wire cutters. I snip mine with the cut on top of the ring so that the end isn’t underneath and poking my finger.

    Step 9

    At this point, I gently squeeze the newly cut tip of wire with my pliers to snug it in so it won’t catch or scratch.

    Step 10

    At this point, I transfer the ring to an unmarked wooden mandrel. My mandrel is rather scuffed up at this point, as you can see in the picture, from this part of the project, and I used one of the inexpensive ones sold in the wire wrapping tools page.

    Your ring will not be perfectly shaped after you’ve finished the wrapping and the sides. I put the ring onto my “cheap” mandrel, and push it firmly down all the way. I turn it around in a circle a few times, and this brings the ring back to the nice, round shape it ought to have. It is also where I straighten out any problems. If the side loops don’t fit quite tightly together, you can gently manipulate them into place with pliers while the ring is snug on the mandrel.

    Step 11

    And that’s it, folks! Ready to wear… (and ready to go make another one)

    Variations

    I used the same technique to make a sweet little ring out of an onion cut green amethyst stone. I had to use a skinnier wire (24 gauge) with this gem, so to make the ring a little stronger, I cut the wire a little longer, and crossed it around the back of the mandrel twice instead of once, for a four-strand wide band rather than a two-strand wide band.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s